Extended Baseband Video Balun - FBNC to Screw Terminals

Extended Baseband Video Balun - FBNC to Screw Terminals from NetConnex. The ETS PV840 Extended Baseband Video Baluns allows you the freedom to use UTP instead of costly coax to transmit baseband video signals throughout your facility, with better signal characteristics, at a lower cost. Depending on your application, you may be able to utilize previously installed wiring, with a corresponding dramatic improvement in cost of installation.

Single, Dual and Quad baseband video baluns are available. Using the PV845, Quad Balun. You can transmit 4 distinct baseband video signals on a single run of Cat5 or better UTP, utilizing all four pairs in the cable. Since each pair has a carefully balance signal on it, you can run video in two directions on different pairs simultaneously.

The PV840 Series of baluns supports color video at distances in excess of 330 meters, depending on cable type. Black and white signals will typically be supported up to 750 meters.

Applications

• All baseband video applications
• Security and Surveillance
• Video Terminals, Displays Features/Advantages
• Use UTP for long distance signal transmission with superior performance and easy, low cost installation
• Greater stability with wider bandwith (0 to 60 MHz)
• Rugged plastic cases
• Made in USA. 100% QA. Specifications
• Bandwith Flat to 60 MHz
• Connectors BNC (female to male) to RJ45 Jack
• Crosstalk >50dB
• Dimensions 46mm x 25mm x 19mm, 66mm x 66mm x 28mm (PV845, 846, 847)

Click Here for More Info

AES/EBU Digital Audio Balun Panel - 8 Chan M-XLR to BNC

AES/EBU Digital Audio Balun Panel - 8 Chan M-XLR to BNC from NetConnex. ETS, long a leader in baluns for computer networks, applies our expertise in Balanced Line technology to the XLR to BNC Digital Audio Baluns (DAB) and DAB Panels. The PA810 Series of Baluns and balun panels from ETS are designed to connect AES/EBU signals from XLR output equipment into standard 75O coax cabling systems. These baluns perform precise impedance matching and signal balancing, allowing AES/EBU signals to be transmitted with great signal integrity and longer runs over coaxial cable than can be achieved with STP wiring. Isolated versions are available for VDA and router applications.

The newest members of this family are the PA818-X Digital Audio Panels. Incorporating all of the functionality of our baluns in a convenient, 8 channel, single rack height unit, an isolated outputs and monitor ports for each channel are standard.

Features/Advantages

• Converts AES/EBU digital audio between balanced 110O XLR and unbalanced 75O BNC
• Seperate baluns, or rack mountable panel versions
• Panel mount has monitor port for each channel
• Available in isolate versions, to route signals via video patch bays, eliminate ground loops
• 10 dB Pad available to attenuate signals to 1 VP-P for compatibility with VDA and router equipment
• Metal cases, chassis
• Made in USA. 100% QA. Specifications
• Bandwith 20 kHz to 60 MHz (1 dB)
• Connectors XLR to BNC
• Insertion Loss <0.15dB
• Max Signal 5V P-P
• Impedance Match 75O to 110O
• Comm Mode Reject >40dB up to 40 MHz
• Dimensions Panels: 1 RU x 37mm deep, Baluns 20.3mm dia. x 89mm long

Click Here for More Info

Gigabit Ethernet Cable Clamp - Common Mode Noise Tester

Gigabit Ethernet Cable Clamp - Common Mode Noise Tester from NetConnex. ETS announces the availability of the CC-101, a cable clamp for injecting common mode current into a Cat5 cable in order to test gigabit Ethernet for common mode noise.

Build according to the 802.3 requirements are detailed in annex 40B of the 1000BaseT standard, the clamp is used in the common mode noise rejection test of section 40.6.1.3.3.

Specifications

• Input 50 ohm female BNC
• Return Loss Guaranteed to exceed 30 dB
• Output 50 ohm female NC (requires 1% 50 ohm load)
• Cable aperture 1/4" copper tube
• Assembly 6 Allen head screws
• Release screws, remove top, insert wire per IEEE 802.3 1000BaseT document, replace top, and reapply screws.
• NoteIt is important to properly tighten screws to assure continuous contact between the two halves of the copper tubing.

Click Here for More Info

Ultra Broadband Video Balun - Female BNC to RJ45 jack pins 4 & 5

Ultra Broadband Video Balun - Female BNC to RJ45 jack pins 4 & 5 from NetConnex. Expanding the territories opened by the Broadband Video Baluns, ETS introduces the PV884 and PV885 - Ultra Broadband Video Baluns. The frequency range has been increased and EMI reduced, both due to enhanced filtering and an all metal enclosure.

FCC requirements preclude boosting signals levels to the values required to guarantee preset distances. Distance achievable is a function of signal level, balance and the degree to which the cable used unbalances the signal. Cat5e maintains signal balance at least 5 dB better than Cat5. Level 7 equivalent cable is another 5 dB better, providing for a signal drive level of not more than 46 dBmV.

Features/Advantages

• Transport ALL CATV spectrum video signals over UTP
• Up to 120+ channels (850 MHz) in CATV spectrum
• Low cost solution for moves, adds and changes by reducing costs of cable and associated labor of rewiring.
• Shielded metal enclosure
• Made in USA. 100% QA. Specifications
• Bandwith 20 MHz to 850 MHz - CATV to 120+, off air channels 2 to 75.
• Connectors BNC or F connector to RJ45, pins 4, 5.
• Impedance 75O unbalanced to 100O balanced
• Insertion Loss 3 dB up to 350 MHz; 5 dB up to 850 MHz
• Return Loss 16 dB
• Common Mode 40 dB
• Media Category 5e or better UTP
• Dimension 25mm x 25mm x 70mm

Click Here for More Info