4u Cat6 Patch Panel - Rack Mount - UnShielded - 96 Port

NetConnex's 4u Cat6 Patch Panel - Rack Mount - UnShielded - 96 Port is intended for high speed LAN transmission rates up to 1 Gigabit. These patch panels were developed with proprietary printed circuit board technology which results in superior performance that meets or exceeds TIA/EIA-568-B.2 specifications. The new version of the 110D terminal block can be used with both a Krone or a 110 Punch Down Tools. The terminal block on our CAT 6 patch panels features both the 568B and 568A color codes on the new version 110D IDC terminal block to ease the task of installation.

• Port: 12,16,24,32,48,72,96 ports Available
• Terminal Block Type: Standard 110D IDC and Krone IDC
• Category Rating: Category 6
• Wiring: A=T568A,B=T568B,C=T568A & T568B combination (for new 110D and krone IDC)
  

Click Here for More Info

19" GoldX CAT5e Patch Panel - 24 Port Rack Mount

24 Port Patch Panel 24 Karat Quality Patch Panel allowing for the industry standard wiring of multiple networking connections into a single location inside a building. Using this patch panel to consolidate all the network connections in your house or office near your concentrator. It does not matter if it is an Ethernet hub, an Ethernet switch, or an Ethernet/broadband router. This will give you a single location for troubleshooting network problems and a single place to make changes to you network configuration. There are inherent problems with terminating the end of the cable that runs through you walls. Two are 1) if the connector goes bad and you do not have enough cable to terminate it again, you must pull another wire, 2) expansion and contraction from the movement of the wire will loosen the crimp of the connector on to the cable, Using a patch panel eliminates these and other problems by: 1) having a mounted place that the wires terminate to. 2) using an insulation displacement connection (IDC) instead of a crimp connection. 3) uses a patch cable that is easer to remove and replace if you have to move the concentration equipment.

• Gold plated contacts
• Premium quality
• Category 5e certified
• Wall mount bracket included
• Standard 19 inch wide equipment rack mountable
• Sturdy aluminum plate around the RJ45 jacks
• Industry standard 110 or Krone IDC connectors
• Designed for high speed transmissions for optimal performance
• Color coded TIA/EIA 568a (International) and 568b (AT&T Standard) wiring for easy installation

Click Here for More Info

2u Blank Patch Panel - RJ11, RJ12, RJ45 - 24 Port

NetConnex's Blank 24 Port Patch Panel is fully compatible all the NetConnex's RJ11/12 Snap-in Keystones, CAT5e RJ 45 Snap-in Jacks, CAT6 RJ45 Snap-In Keystone Jacks and the NetConnex's CAT5e Snap-In Feed Through Keystone Jacks.

Click Here for More Info

GoldX Punch Down Tool - 110 Blade Included

Impact Punch Down Tool 24 Karat Quality Impact Punch Down Tool with 110 style blade. Using this tool will help you ensure that you have well seated connections on all industry standard 110 style IDC connectors.  The dual impact settings is helpful for when you find that the wire is just not seating right.  Standard blades are used in this tool, so if you damage or break the blade, or if you find that a job requires a Krone tool or 66 style block tool, just pick up a blade and use the same impact handle.  The blade which is included has both a punch only and a punch and cut side.   If you have need to punch without trimming any extra wiring, then use the punch only side.   If you want to punch and trim at the same time, then use the side that has "cut" stamped into it.

• Sturdy handle
• Blade included
• Premium quality
• Replaceable blade
• Blade Storage in handle
• Dual impact settings, low and high
• For use with industry standard 110 connectors

Click Here for More Info